[WELL Lab] Disposable Coveralls Compared: PBS-500 vs 1000 vs 1500 vs 2000

By WELL Technical Team · Jim Wang

A side-by-side comparison of four disposable coveralls — fabric structure, seam construction, protection class, and measured repellency data with a selection table.

When customers ask about disposable coveralls, the question is rarely "do you have them" — it is "you have so many models, which one do I buy?"

That is hard to answer from a catalogue, because the answer is not in the product. It is in your workshop. The same coverall is the wrong choice in a paint shop and in a food plant.

So here is the full range, laid out plainly. Match it to your situation.

1. The range at a glance

  • Model:PBS-500;Fabric:SMS microporous non-woven;Colour:Blue / White;Seams:4-thread + taped;Main use:Dust environments, cost-sensitive
  • Model:PBS-1000;Fabric:Microporous PE/PP laminate;Colour:White;Seams:Taped seams;Main use:Chemical handling, light splash (Type 5/6)
  • Model:PBS-1500;Fabric:Breathable film front + SMS back;Colour:White / blue trim;Seams:Taped seams;Main use:Painting, shipbuilding, wind power
  • Model:PBS-2000;Fabric:Microporous breathable film;Colour:White;Seams:Overlock-sealed;Main use:Precision assembly, surface treatment

A table only goes so far. Here are the differences that actually matter.

2. Difference 1: fabric structure decides breathability vs liquid holdout

PBS-500 uses SMS microporous non-woven — a high-breathability route. It is our economy model: for dust environments where cost matters but protection requirements are specific.

PBS-2000 uses a microporous breathable film laminate, and takes a different position entirely — ultra-low particle shedding. It resists shedding during use, greatly reducing fibre contamination risk, and filters particles down to 1 micrometre. For precision assembly, surface treatment and dust-sensitive lines, it fits better than a general-purpose coverall.

产品资料:PBS-2000 Coverall

PBS-1500 is the unusual one in this group. It uses a hybrid front-and-back construction: breathable film at the front (liquid holdout), SMS at the back (breathability).

Why? Painting, shipbuilding and wind-power work share a contradiction — the front must resist paint mist and solvents, while the back must dissipate heat. A fully liquid-tight suit is unbearable; a fully breathable one leaves the front exposed. The hybrid answers exactly that.

It is also silicone-free, which matters enormously in painting. Silicone contamination causes cratering in the finish — the cardinal sin of any paint shop.

3. Difference 2: seam construction — the most overlooked detail

Whether a coverall leaks is decided at the seams, not the fabric.

Liquids and particles get in through needle holes. All four models therefore treat the seams — either 4-thread stitching with taped edges, or taped seams — covering the stitch line completely.

The difference is in finish: PBS-2000 uses overlock-sealed seams, giving fuller edge coverage. That is part of why it suits cleanroom-adjacent work.

If you have bought coveralls that look identical but cost far less, the difference is probably here — seams untreated, or treated badly.

4. Difference 3: protection class, under Chinese and European standards

PBS-500 corresponds to European Type 5 (solid particle protection).

PBS-1000 passes GB 24539-2021 as Type 5 / 6 (particle protection plus limited liquid splash).

PBS-1500 and PBS-2000 are both Type 5/6.

One warning: Type 5 protects against particles, Type 6 against limited liquid splash. They are not interchangeable. If there is chemical splash risk on site, Type 6 is the starting point.

5. Difference 4: measured data (do not take my word for it)

Claiming "good protection" means nothing. Here is the test data.

PBS-1000 chemical penetration resistance:

  • 30% sulphuric acid:98.1%
  • 10% sodium hydroxide:92.3%
  • n-butanol:93.4%
  • o-xylene:94.4%

PBS-2000 chemical penetration resistance:

  • 30% sulphuric acid:92.1%
  • 10% sodium hydroxide:95.9%
  • n-butanol:92.0%
  • o-xylene:95.2%

Mechanical performance comparison:

  • Property:Abrasion resistance;PBS-1000:>400 cycles (class 4);PBS-2000:>2000 cycles (class 6)
  • Property:Puncture resistance;PBS-1000:6 N;PBS-2000:—
  • Property:Trapezoidal tear;PBS-1000:—;PBS-2000:30 N / 61 N
  • Property:Seam strength;PBS-1000:—;PBS-2000:96 / 126 / 122

Two numbers are worth noting: PBS-2000 resists abrasion more than five times longer than PBS-1000 — that decides service life under repeated rubbing. And both hold back over 92% of the test liquids, meaning routine acids and alkalis are comfortably handled.

PBS-1000 also has a surface resistivity of 1.84×10⁹ Ω·m, which corresponds to antistatic performance — a hard requirement where flammable or explosive atmospheres are present.

6. How to choose: match your situation

  • Dust work, cost-sensitive:PBS-500
  • Chemical handling, possible splash:PBS-1000
  • Painting, shipbuilding, wind power:PBS-1500
  • Precision assembly, surface treatment:PBS-2000

提示:If unsure, ask one question: is the main risk dust, liquid, or cleanliness? Three answers map to three levels. No agonising required.

7. One last point

These four are not "better" and "worse". They are four answers to four situations. Choose wrong and you either under-protect, or pay for protection your team will not wear.

If you are still unsure, send us your working scenario, the chemicals involved, and your cleanliness requirements. We will give you a specific recommendation.

For the fundamentals, start here: 一次性防护服防护等级解读:Type 3/4/5/6 到底代表什么防护? (中文), 一次性防护服克重 35g/45g/55g/65g/87g/112g 怎么选? (中文), 【维尔实验室】防化服选型指南:轻型、中型、增强型 3 大类别与典型场景 (中文).

For samples, test reports or volume pricing, please contact: zhimin.wang@well-protection.com / +86 182 1771 2651     (021) 6225 5575

For the fundamentals, start here: 

 

浏览全部产品:产品中心

常见问题

Q&A

넳 넲